Now available in the EU from Welectron (Germany) What it is: Moteino is a versatile low power Arduino based on the Atmel ATMega328P microcontroller. Please see the Moteino Guide for full specs and details. To make a wireless link you will need at least 2 Moteinos. Alternatively this is compatible with other Arduinos that use any RFM69 transceiver. Here are a few features and highlights of Moteino: Low cost Arduino fully compatible with the Arduino IDE Includes...

IMPORTANT: Please see the Moteino 8Mhz Guide before you use this board, also read information below. What it is: Moteino 8Mhz is the LDO-less variant of the regular Moteino. It is clocked at 8Mhz, has different fuses to run the Brown Out at 1.8v and is designed for powering it from voltages less than 3.6V. The differences to regular Moteino are: no LDO linear regulator the VIN and 3v3 pins are connected and can be considered the same must be powered from...

What it is: This is the trace antenna variant of the regular Moteino, otherwise all specifications are identical. The included antenna is tuned for 868-915mhz and can be used when a transceiver is attached on the bottom. Moteino is a low cost wireless Arduino based on the Atmel ATMega328P microcontroller. For a detailed guide please see this dedicated page. Here are a few features and highlights of Moteino: Low cost Arduino fully compatible with the Arduino IDE The...

Now available in the EU from Welectron (Germany) Ultra low power development board based on the SAMD21G18A Cortex M0+ 32bit ARM processor. Designed for use with RFM69 transceivers and RFM95/RFM96 LoRa transceivers. Ideal in projects where battery life is critical and which require the computing and peripheral diversity of SAMD ARM processors. Guide & drivers: Be sure to check out the MoteinoM0 Guide page for usage details and other more in-depth...

What it is: MoteinoMEGA is designed for use with RFM69 HCW/CW and RFM95/RFM96 LoRa transceivers. MoteinoMEGA is a wireless Arduino based on the Atmel ATMega1284P microcontroller: Fully compatible with the Arduino IDE 128KB sketch flash memory 16KB RAM! (compare to just 2KB on the atmega328p) 4KB EEPROM Low power battery operation friendly just as the regular Moteino 3.3V onboard regulator (MCP1703) provides up to 250mA, input up to 16V...

What it is: This is the R4 revision of MoteinoMEGA, it is designed for use with RFM69 and LoRa transceivers (RFM69HCW, RFM69CW, RFM95, can also take RFM12B). It has an included PCB trace antenna tuned for 868-915mhz (yellow PCB edition). MoteinoMEGA is a low cost wireless Arduino based on the Atmel ATMega1284P microcontroller: Low cost Arduino fully compatible with the Arduino IDE 128KB sketch flash memory 16KB RAM! (compare to just 2KB on the atmega328p) 4KB...

Now available in the EU from Welectron (Germany) What it is: This is the R6-USB revision of Moteino, it is designed for use with FSK transceivers (RFM69HCW, RFM69CW) and LoRa transceivers (RFM95, RFM96). See the transceivers guide. Moteino-USB is designed to be used without the need of an additional FTDI adapter. It has a built in USB-Serial FTDI adapter chip, and only a regular micro-USB cable is required for power and programming. Otherwise it has...

What it is: This is the USB variant of the MoteinoMEGA, it is designed for use with RFM69 transceivers and RFM95/RFM96 LoRa transceivers. It has a built in FTDI USB-to-TTL serial chip, and only a micro-USB cable is required for power and programming. Otherwise it has the same features as the non-USB MoteinoMEGA. Now suitable for LoRaWAN with the LMIC option: see this forum thread for details, sample code for reading the EUI64 chip is posted here....

Now available in the EU from Welectron (Germany) What it is: FTDI-Adapter is a USB-Serial bridge so you can upload programs to Moteino or communicate to your microcontroller serial controller through your PC's USB port. The pinout is standard [ GND - CTS - VCC - TX - RX - RTS ] and will work with any Arduino clone that has this as a programming interface. Other examples of compatible FTDI adapters you can use to power/program your Moteinos: USB BUBII, FTDI cables here and here, FTDI...

Winbond W25X40CL 4Mbit (512KB) serial SPI flash memory chip. 8-SOIC JEDEC package (3.9mm width, 0.154"). Can be soldered to Moteino (R2) for data logging purposes or for wireless programming. Or you may order your Moteino with the Flash chip pre-soldered. Arduino SPIFlash library and example: https://github.com/LowPowerLab/SPIFlash Related blog post: http://lowpowerlab.com/blog/2013/04/04/spiflash-memory-library-for-arduinomoteino/ Note: for wireless programming you...