Components

PRODUCT ID:185

Now available in the EU from Welectron (Germany) Highly accurate I2C BME280 temperature + humidity + atmospheric pressure sensor...

Now available in the EU from Welectron (Germany) Highly accurate I2C BME280 temperature + humidity + atmospheric pressure sensor offer a stable ultra low power platform for an environment sensory board. same sensor found on the WeatherShield ultra low power sensor - see the no-battery solar+supercap Moteino project that runs perpetually without a battery must be powered from 3.3v (via "3V" pin) MoteinoM0 PCB flat-mount breadboard compatible header...

$16.95

In Stock

LSM9DS1 9DoF IMU Breakout [RETIRED]

PRODUCT ID:186

The LSM9DS1 is a 3-in-1 sensor housing a 3-axis accelerometer + 3-axis gyroscope + 3-axis magnetometer (9 degrees of freedom) in a single tiny chip. This...

The LSM9DS1 is a 3-in-1 sensor housing a 3-axis accelerometer + 3-axis gyroscope + 3-axis magnetometer (9 degrees of freedom) in a single tiny chip. This breakout is wired for I2C operation of the LSM9DS1. must be powered from 3.3v (via "3V" pin) MoteinoM0 PCB flat-mount breadboard compatible header spacing see schematic below for i2c addressing 9 degrees of freedom What you get: SMD Assembled and tested unit, no headers soldered You may solder...

$19.95

Out of Stock

WeatherShield

PRODUCT ID:123

Highly accurate I2C BME280 temperature + humidity + atmospheric pressure sensor offer a stable ultra low power platform for an environment sensory...

Highly accurate I2C BME280 temperature + humidity + atmospheric pressure sensor offer a stable ultra low power platform for an environment sensory board. Can be stacked directly with Moteino and MoteinoUSB (not on MoteinoMEGA). Onboard battery monitor from VIN, reading on A7, through a 2/3 (1MEG+2MEG resistor divider). Unpopulated Si7021 pad allows soldering that sensor yourself if you'd like. See the new WeatherShield Guide here! IMPORTANT: To reduce idle current to ~1uA, the...

$17.95

Only 7 left

OMRON EE-SY310 photo reflective sensor

PRODUCT ID:85

This sensor is also available on a breakout board with all necessary components to interface it directly to your microcontroller. What it is: Dark...

This sensor is also available on a breakout board with all necessary components to interface it directly to your microcontroller. What it is: Dark ON model (EE-SY310) Digital output HIGH/LOW depending if it detects a dark/bright spot Meant to detect revolutions on spinning wheels/gears that are marked with a dark spot can also be used to detect a water meter dial or a conventional electric meter containing a spinning dial with a dark line wide supply voltage...

$2.95

Out of Stock

Serial Flash 4Mbit

PRODUCT ID:72

Winbond W25X40CL 4Mbit (512KB) serial SPI flash memory chip. 8-SOIC package (3.9mm width, 0.154"). Can be soldered to any Moteino for data logging...

Winbond W25X40CL 4Mbit (512KB) serial SPI flash memory chip. 8-SOIC package (3.9mm width, 0.154"). Can be soldered to any Moteino for data logging purposes or for wireless programming. Or you may order Moteinos with the Flash chip pre-soldered. Arduino SPIFlash library and example: https://github.com/LowPowerLab/SPIFlash Related blog post: http://lowpowerlab.com/blog/2013/04/04/spiflash-memory-library-for-arduinomoteino/ Note: for wireless programming you will need...

$2.95

In Stock

Nokia 5110 LCD

PRODUCT ID:54

The popular Nokia 5110 LCD (84*48px) usable with various graphic libraries for Arduino. It is optionally used in the MightyHat kit. The recommended...

$7.95

Out of Stock

HC-SR04 sensor

PRODUCT ID:112

HC-SR04 ultrasonic sensor. Works at 5V Used in the Sump pump alert project See this tutorial for how to connect it to your Arduino...

$5.00

Only 5 left

OLED Display 128x64px

PRODUCT ID:135

Standard 0.96" OLED Display for Moteino / Arduino projects. Pinout: [GND, VCC, SCL, SDA] VIN: 3-5V 128x64px Comes with soldered...

$7.95

In Stock

Omnipolar Magnetic/Hall Sensor

PRODUCT ID:57

Digital hall effect sensor (Honeywell SS451A, TO92-3 package) used in the Mailbox notifier project and in GarageMote. Digital output that changes...

Digital hall effect sensor (Honeywell SS451A, TO92-3 package) used in the Mailbox notifier project and in GarageMote. Digital output that changes state when any magnetic field is detected nearby. This is not an analog hall effect sensor, it only has 2 output states: 0, 1. See datasheet for more details. It is an OMNIPOLAR magnetic sensor, meaning it will detect both North & South poles, which means you don't have to worry about orientation! It replaces the older...

$2.20

Out of Stock

PIR motion sensor

PRODUCT ID:113

PIR motion sensor (HC-SR501) Works at 5-16V Used in the MotionMote and MailboxAlert projects Has 3 connections: GND, VCC, OUT OUT...

$5.00

Out of Stock

Lithium Ion Polymer Battery 3.7v 1200mAh

PRODUCT ID:200

Lithium Ion Polymer Battery 1200mAh output at 3.7v nominal 4.2V when fully charged includes protection circuitry (over...

Lithium Ion Polymer Battery 1200mAh output at 3.7v nominal 4.2V when fully charged includes protection circuitry (over charging, overload) JST PH2.0 connector mating with JST connectors in all our battery powered products like CurrentRanger, MoteinoM0, as well as virtually all such battery powered boards at other vendors dimensions: 1.75*1.5", 0.26" thick (45*37mm, 6.7mm thick) 50mm lead length 28g (1oz) Important notes...

$9.95

Only 23 left

12mm push button

PRODUCT ID:109

High quality low profile OMRON B3F tactile momentary push button measuring 12 X 12 X 6mm. Can be used on a breadboard. Optional square caps can...

$0.50

Out of Stock

3-pin Screw Terminals

PRODUCT ID:107

3-pin Screw Terminals 5.08mm pin spacing. Datasheet & drawing: http://www.on-shore.com/sites/default/files/manuals/osttcxx2162.pdf

$0.95

Out of Stock

Banana to Hook Test Clip Cables - 40"

PRODUCT ID:183

Blue/Red pair of flexible silicone rubber cable - banana plug to hook clip. Having good cables with low resistance is essential for accurate measurements...

$9.95

Out of Stock

Helical Antenna

PRODUCT ID:160

There are two types of helical antennas: 868Mhz Helical Antenna (2dBi, 13mm, 50ohm) 915Mhz Helical Antenna (2dBi, 12.5mm, 50ohm) They...

$1.95

In Stock

LED Power switch (latching)

PRODUCT ID:150

Latching button with GREEN illuminated power symbol (16mm mounting hole). High quality chrome metal body, includes rubber seal ring for...

Latching button with GREEN illuminated power symbol (16mm mounting hole). High quality chrome metal body, includes rubber seal ring for nice flush mounting that protects your enclosure. Switch is LATCHING but pressed only half way it can still be used as momentary (it will only latch if you push it all the way). To unlatch it, press again. Perfect for ATXRaspi. Similar switch used in the ATXRaspi demo video except this is latching (not momentary). For...

$7.95

Out of Stock

LED Power switch (momentary)

PRODUCT ID:118

Momentary button with GREEN illuminated power symbol (16mm mounting hole). High quality chrome metal body, includes rubber seal ring...

$7.95 $6.95

Only 18 left

Piezo Buzzer

PRODUCT ID:124

Piezo buzzer that can be driven from a single Moteino pin. The loudest frequencies are around 4200-4800Hz. It is used in the MotionOLEDMote and there...

$1.50

In Stock

Premium jumper wire

PRODUCT ID:154

Premium jumper wire for ATXRaspi. When used to power your Pi these wires help eliminate Low Voltage warnings. They will support a much higher...

Premium jumper wire for ATXRaspi. When used to power your Pi these wires help eliminate Low Voltage warnings. They will support a much higher load than cheap chinese "dupont" wires. 4 pack 4 color (usually red+black for power, and another 2 colors for BOOTOK and SHUTDOWN) 6" (15cm) length Female-Female connectors for easy mating with your Pi header This is what typical cheap "Dupont" jumper wires looks like: They cause the low voltage warnings especially...

$3.95

Out of Stock

Relay (3V)

PRODUCT ID:104

G5V-1-DC3 3V relay, used in GarageMote. Datasheet: click here. Can be driven by 2 Arduino pins (set both to HIGH), or through a transistor. Layout: SPDT...

G5V-1-DC3 3V relay, used in GarageMote. Datasheet: click here. Can be driven by 2 Arduino pins (set both to HIGH), or through a transistor. Layout: SPDT (1 Form C) Coil Data Switches from 1 mA to 1 A Coil Power: 150mW Nominal Voltage: 3Vdc Pick-Up Voltage: 2.4Vdc Drop-Out Voltage: 0.3Vdc Maximum Voltage: 4.5Vdc Coil Resistance: 60ohm Contact Data Contact Rating: 0.5A 125Vac / 1A 30Vdc Contact material: Silver (Ag), Gold (Au) Maximum...

$2.80

Out of Stock

Rocking LED switch

PRODUCT ID:151

Rocking (latching) switch (21x15mm), suitable for latching switch operation with ATXRaspi. Black body with GREEN LED backlight. Can...

$4.95

Out of Stock

Slide switch SPDT (Straight)

PRODUCT ID:84

SPDT Slide switch - Straight, standard 0.1" spaced connections (breadboard friendly)

$0.50

Out of Stock

SOT23/SC70 DIP Breakout

PRODUCT ID:125

DIP breakout board for SOT23 and SC70 (aka SOT363) packages. Pins are 0.1" spaced for breadboard friendly applications. Easily break out very...

$0.95

In Stock

u.FL connector

PRODUCT ID:153

u.FL RF connector (50ohm) Can be soldered to Moteino (R5+), MoteinoMEGA, MightyHat.

$0.95

Out of Stock

Buck Regulator - 5V/1.5A

PRODUCT ID:133

Highly efficient buck regulator that can easily regulate 5V from typical 12-24VAC sources (rectified through a 1N4007 diode). This was the regulator...

$9.95

Only 2 left

Capacitor - 100uF/25V

PRODUCT ID:122

KEMET aluminum capacitor 100uF, radial, 20%, 25V.

$0.35

Out of Stock

Capacitor 1000uF

PRODUCT ID:65

Generic aluminum capacitor: 1000uF radial 20% 10V rating Through hole (lead spacing: 3.5mm) Compact size (without...

$0.50

In Stock

Capacitor 470uF/25V

PRODUCT ID:167

Generic aluminum capacitor: 470uF 25V radial - 10mm diameter 20% 105C operation Through hole (lead spacing: 5mm) Size...

$0.49

Only 15 left

LED - RGB (10mm)

PRODUCT ID:121

RGB LED, 10mm, diffused white color, forward voltage: ~1.8-2.8V.

$0.30

Out of Stock

Low power LED (3mm)

PRODUCT ID:102

Low power LED, 3mm, 2ma, diffused tinted, forward voltage: ~1.8-1.85V. Used in various Moteino projects, can be used with a 1K-1.5Kohm resistor...

...

$1.25

Out of Stock

MiniBoost 5V/1A Booster

PRODUCT ID:137

DIP boost regulator that can supply 5V/1A for your project from a LithiumPolymer or equivalent battery. Same size and pinout as the popular 7805...

$7.95

Out of Stock

NPN Transistor 2N3904

PRODUCT ID:58

...

$0.50

Out of Stock

PNP Transistor 2N3906

PRODUCT ID:80

2N3906 - PNP general purpose amplifier transistor Datasheet: http://www.fairchildsemi.com/ds/2N/2N3906.pdf For the mailbox notifier...

$0.50

Out of Stock

Shottky Diode

PRODUCT ID:64

Shottky Diode (1N5818), 30V, 1A, D041 package. Forward voltage: 550ma @ 1A. Used in the WattMote project to block reverse voltage from the KillAWatt....

$0.75

Only 5 left

Solar Panel 6V/1W

PRODUCT ID:166

Small Solar Panel, perfect for small low power projects that charge a Super Capacitor and keep a Moteino perpetually powered without a battery! Check...

$4.95

Out of Stock

Supercapacitor - 7.5F 5.4V 55mOhm-ESR

PRODUCT ID:163

AVX 7.5F Supercapacitor, used in the now famous Moteino + WeatherShield + Small Solar Cell + Supercapacitor project. Unaffected performance and...

AVX 7.5F Supercapacitor, used in the now famous Moteino + WeatherShield + Small Solar Cell + Supercapacitor project. Unaffected performance and operation in extreme hot or freezing temperatures. Perfect for ultra low power nodes that need to run perpetually (charging via tiny solar cell). Specifications: 7.5F (farad) capacity (+/-20%) 5.5V rating 55mOhm ultra low ESR Through hole (spacing: 17mm) Dimensions (without leads): 32L x 25W x 13H mm AVX Part...

$9.95

Out of Stock