LowPowerLab Forum

I modified the shutdown script to work with recalbox if anyone is interested.

Make sure you remount the filesystem as read write

mount -o remount, rw /

echo '#!/bin/bash

#This is GPIO 7 (pin 26 on the pinout diagram).
#This is an input from ATXRaspi to the Pi.
#When button is held for ~3 seconds, this pin will become HIGH signalling to this script to poweroff the Pi.
SHUTDOWN=7
REBOOTPULSEMINIMUM=200      #reboot pulse signal should be at least this long
REBOOTPULSEMAXIMUM=600      #reboot pulse signal should be at most this long
echo "$SHUTDOWN" > /sys/class/gpio/export
echo "in" > /sys/class/gpio/gpio$SHUTDOWN/direction

#Added reboot feature (with ATXRaspi R2.6 (or ATXRaspi 2.5 with blue dot on chip)
#Hold ATXRaspi button for at least 500ms but no more than 2000ms and a reboot HIGH pulse of 500ms length will be issued

#This is GPIO 8 (pin 24 on the pinout diagram).
#This is an output from Pi to ATXRaspi and signals that the Pi has booted.
#This pin is asserted HIGH as soon as this script runs (by writing "1" to /sys/class/gpio/gpio8/value)
BOOT=8
echo "$BOOT" > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio$BOOT/direction
echo "1" > /sys/class/gpio/gpio$BOOT/value

echo "ATXRaspi shutdown script started: asserted pins ($SHUTDOWN=input,LOW; $BOOT=output,HIGH). Waiting for GPIO$SHUTDOWN to become HIGH..."

#This loop continuously checks if the shutdown button was pressed on ATXRaspi (GPIO7 to become HIGH), and issues a shutdown when that happens.
#It sleeps as long as that has not happened.
while [ 1 ]; do
  shutdownSignal=$(cat /sys/class/gpio/gpio$SHUTDOWN/value)
  if [ $shutdownSignal = 0 ]; then
    /bin/sleep 0.2
  else 
    pulseStart=$(python -c'import time; print int(round(time.time() * 1000))') # mark the time when Shutoff signal went HIGH (milliseconds since epoch)
    while [ $shutdownSignal = 1 ]; do
      /bin/sleep 0.02
      pulseNow=$(python -c'import time; print int(round(time.time() * 1000))')
      pulseDiff=$pulseNow-$pulseStart
      if [ $(($pulseNow-$pulseStart)) -gt $REBOOTPULSEMAXIMUM ]; then
        echo "ATXRaspi triggered a shutdown signal, halting Rpi ... "
        poweroff
        exit
      fi
      shutdownSignal=$(cat /sys/class/gpio/gpio$SHUTDOWN/value)
    done
    #pulse went LOW, check if it was long enough, and trigger reboot
      pulseNow=$(python -c'import time; print int(round(time.time() * 1000))')
      if [ $(($pulseNow-$pulseStart)) -gt $REBOOTPULSEMINIMUM ]; then
      echo "ATXRaspi triggered a reboot signal, recycling Rpi ... "
      reboot
      exit
    fi
  fi
done' > /etc/shutdowncheck.sh
chmod 755 /etc/shutdowncheck.sh
Just save as shutdownchecksetup.sh and set permissions/chmod +x the file.

Then edit one of the files in /etc/init.d

I put mine in /etc/init.d/S31emulationstation

Like this at the bottom:

esac

/etc/shutdowncheck.sh &

exit $?

That was it.  Works well.

Thanks

hi

this work with  recalbox 4.0.0 build 23?

thanks

@djanice1980 - thanks for sharing this!