Is there a sketch which can be used to send periodic weather readings from the WeatherShield with Moteinos equipped with the rf96 transceiver?
Can the sketch "BME280_ino" be modified to work with the rf96? If so, what changes need to be made?
When compiling "BME280", I get the following errors:
BME280_ino.ino:94:1: error: 'period_t' does not name a type
BME280_ino.ino:128:3: error: 'RFM69_ATC' does not name a type
BME280_ino.ino: In function 'void setup()':
BME280_ino.ino:148:3: error: 'radio' was not declared in this scope
BME280_ino.ino:162:74: error: 'RF69_433MHZ' was not declared in this scope
BME280_ino.ino:162:105: error: 'RF69_868MHZ' was not declared in this scope
BME280_ino.ino:182:14: error: 'RF69_SPI_CS' was not declared in this scope
BME280_ino.ino: In function 'void loop()':
BME280_ino.ino:227:5: error: 'radio' was not declared in this scope
BME280_ino.ino:268:1: error: a function-definition is not allowed here before '{' token
BME280_ino.ino:287:1: error: a function-definition is not allowed here before '{' token
BME280_ino.ino:293:1: error: expected '}' at end of input
It would help us help you if you posted the code.
Sorry. Here is the code:
// **********************************************************************************************************
// WeatherShield R2 (BME280 sensor) sameple sketch that works with Moteinos equipped with RFM69W/RFM69HW
// It sends periodic weather readings (temp, hum, atm pressure) from WeatherShield to the base node Moteino
// For use with MoteinoMEGA you will have to revisit the pin definitions defined below
// http://www.LowPowerLab.com/WeatherShield
// Example setup (with R1): http://lowpowerlab.com/blog/2015/07/24/attic-fan-cooling-tests/
// **********************************************************************************
// Copyright Felix Rusu 2016, http://www.LowPowerLab.com/contact
// **********************************************************************************
// License
// **********************************************************************************
// This program is free software; you can redistribute it
// and/or modify it under the terms of the GNU General
// Public License as published by the Free Software
// Foundation; either version 3 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will
// be useful, but WITHOUT ANY WARRANTY; without even the
// implied warranty of MERCHANTABILITY or FITNESS FOR A
// PARTICULAR PURPOSE. See the GNU General Public
// License for more details.
//
// Licence can be viewed at
// http://www.gnu.org/licenses/gpl-3.0.txt
//
// Please maintain this license information along with authorship
// and copyright notices in any redistribution of this code
// **********************************************************************************
#include <SPI.h>
#include <RH_RF95.h>
#define FREQUENCY 434
//#include <RFM69.h> //get it here: https://github.com/lowpowerlab/rfm69
//#include <RFM69_ATC.h> //get it here: https://github.com/lowpowerlab/rfm69
//#include <RFM69_OTA.h> //get it here: https://github.com/lowpowerlab/rfm69
#include <SPIFlash.h> //get it here: https://github.com/lowpowerlab/spiflash
#include <SPI.h> //included in Arduino IDE (www.arduino.cc)
#include <Wire.h> //included in Arduino IDE (www.arduino.cc)
#include <SparkFunBME280.h>//get it here: https://github.com/sparkfun/SparkFun_BME280_Breakout_Board/tree/master/Libraries/Arduino/src
//#include <LowPower.h> //get it here: https://github.com/lowpowerlab/lowpower
//writeup here: http://www.rocketscream.com/blog/2011/07/04/lightweight-low-power-arduino-library/
//*********************************************************************************************
//************ IMPORTANT SETTINGS - YOU MUST CHANGE/CONFIGURE TO FIT YOUR HARDWARE ************
//*********************************************************************************************
#define GATEWAYID 1
#define NODEID 40
#define NETWORKID 100
//#define FREQUENCY RF69_433MHZ
//#define FREQUENCY RF69_868MHZ
//#define FREQUENCY RF69_915MHZ //Match this with the version of your Moteino! (others: RF69_433MHZ, RF69_868MHZ)
#define ENCRYPTKEY "sampleEncryptKey" //has to be same 16 characters/bytes on all nodes, not more not less!
#define IS_RFM69HW_HCW //uncomment only for RFM69HW/HCW! Leave out if you have RFM69W/CW!
//*********************************************************************************************
#define ENABLE_ATC //comment out this line to disable AUTO TRANSMISSION CONTROL
#define ATC_RSSI -75
//*********************************************************************************************
#define SEND_LOOPS 15 //send data this many sleep loops (15 loops of 8sec cycles = 120sec ~ 2 minutes)
#define SLEEP_FASTEST SLEEP_15MS
#define SLEEP_FAST SLEEP_250MS
#define SLEEP_SEC SLEEP_1S
#define SLEEP_LONG SLEEP_2S
#define SLEEP_LONGER SLEEP_4S
#define SLEEP_LONGEST SLEEP_8S
period_t sleepTime = SLEEP_LONGEST; //period_t is an enum type defined in the LowPower library (LowPower.h)
//*********************************************************************************************
#define BATT_MONITOR_EN A3 //enables battery voltage divider to get a reading from a battery, disable it to save power
#define BATT_MONITOR A7 //through 1Meg+470Kohm and 0.1uF cap from battery VCC - this ratio divides the voltage to bring it below 3.3V where it is scaled to a readable range
#define BATT_CYCLES 2 //read and report battery voltage every this many sleep cycles (ex 30cycles * 8sec sleep = 240sec/4min). For 450 cyclesyou would get ~1 hour intervals
#define BATT_FORMULA(reading) reading * 0.00322 * 1.475 // >>> fine tune this parameter to match your voltage when fully charged
#define BATT_LOW 3.6 //(volts)
#define BATT_READ_LOOPS SEND_LOOPS*10 // read and report battery voltage every this many sleep cycles (ex 30cycles * 8sec sleep = 240sec/4min). For 450 cycles you would get ~1 hour intervals between readings
//*****************************************************************************************************************************
#ifdef __AVR_ATmega1284P__
#define LED 15 // Moteino MEGAs have LEDs on D15
#define FLASH_SS 23 // and FLASH SS on D23
#else
#define LED 9 // Moteinos have LEDs on D9
#define FLASH_SS 8 // and FLASH SS on D8
#endif
//#define BLINK_EN //uncomment to blink LED on every send
//#define SERIAL_EN //comment out if you don't want any serial output
#ifdef SERIAL_EN
#define SERIAL_BAUD 115200
#define DEBUG(input) {Serial.print(input);}
#define DEBUGln(input) {Serial.println(input);}
#define SERIALFLUSH() {Serial.flush();}
#else
#define DEBUG(input);
#define DEBUGln(input);
#define SERIALFLUSH();
#endif
//*****************************************************************************************************************************
#ifdef ENABLE_ATC
RFM69_ATC radio;
#else
RFM69 radio;
#endif
SPIFlash flash(FLASH_SS, 0xEF30); //WINDBOND 4MBIT flash chip on CS pin D8 (default for Moteino)
BME280 bme280;
char Pstr[10];
char Fstr[10];
char Hstr[10];
char buffer[50];
void setup(void)
{
#ifdef SERIAL_EN
Serial.begin(SERIAL_BAUD);
#endif
pinMode(LED, OUTPUT);
radio.initialize(FREQUENCY,NODEID,NETWORKID);
#ifdef IS_RFM69HW_HCW
radio.setHighPower(); //must include this only for RFM69HW/HCW!
#endif
radio.encrypt(ENCRYPTKEY);
//Auto Transmission Control - dials down transmit power to save battery (-100 is the noise floor, -90 is still pretty good)
//For indoor nodes that are pretty static and at pretty stable temperatures (like a MotionMote) -90dBm is quite safe
//For more variable nodes that can expect to move or experience larger temp drifts a lower margin like -70 to -80 would probably be better
//Always test your ATC mote in the edge cases in your own environment to ensure ATC will perform as you expect
#ifdef ENABLE_ATC
radio.enableAutoPower(ATC_RSSI);
#endif
sprintf(buffer, "WeatherMote - transmitting at: %d Mhz...", FREQUENCY==RF69_433MHZ ? 433 : FREQUENCY==RF69_868MHZ ? 868 : 915);
DEBUGln(buffer);
//initialize weather shield BME280 sensor
bme280.settings.commInterface = I2C_MODE;
bme280.settings.I2CAddress = 0x77;
bme280.settings.runMode = 3; //Normal mode
bme280.settings.tStandby = 0;
bme280.settings.filter = 0;
bme280.settings.tempOverSample = 1;
bme280.settings.pressOverSample = 1;
bme280.settings.humidOverSample = 1;
radio.sendWithRetry(GATEWAYID, "START", 6);
Blink(LED, 100);Blink(LED, 100);Blink(LED, 100);
if (flash.initialize()) flash.sleep();
for (uint8_t i=0; i<=A5; i++)
{
if (i == RF69_SPI_CS) continue;
if (i == FLASH_SS) continue;
pinMode(i, OUTPUT);
digitalWrite(i, LOW);
}
SERIALFLUSH();
readBattery();
}
unsigned long doorPulseCount = 0;
char input=0;
double F,P,H;
byte sendLoops=0;
byte battReadLoops=0;
float batteryVolts = 5;
char* BATstr="BAT:5.00v"; //longest battery voltage reading message = 9chars
byte sendLen;
void loop()
{
if (battReadLoops--<=0) //only read battery every BATT_READ_LOOPS cycles
{
readBattery();
battReadLoops = BATT_READ_LOOPS-1;
}
if (sendLoops--<=0) //send readings every SEND_LOOPS
{
sendLoops = SEND_LOOPS-1;
//read BME sensor
bme280.begin();
P = bme280.readFloatPressure() * 0.0002953; //read Pa and convert to inHg
F = bme280.readTempF();
H = bme280.readFloatHumidity();
bme280.writeRegister(BME280_CTRL_MEAS_REG, 0x00); //sleep the BME280
dtostrf(F, 3,2, Fstr);
dtostrf(H, 3,2, Hstr);
dtostrf(P, 3,2, Pstr);
sprintf(buffer, "BAT:%sv F:%s H:%s P:%s", BATstr, Fstr, Hstr, Pstr);
sendLen = strlen(buffer);
radio.sendWithRetry(GATEWAYID, buffer, sendLen, 1); //retry one time
DEBUG(buffer); DEBUG(" (packet length:"); DEBUG(sendLen); DEBUGln(")");
#ifdef BLINK_EN
Blink(LED, 5);
#endif
}
//When this sketch is on a node where you can afford the power to keep the radio awake all the time
// you can make it receive messages and also make it wirelessly programmable
// otherwise this section can be removed
/*
if (radio.receiveDone())
{
boolean reportStatusRequest=false;
DEBUG('[');DEBUG(radio.SENDERID);DEBUG("] ");
for (byte i = 0; i < radio.DATALEN; i++)
DEBUG((char)radio.DATA[i]);
flash.wakeup();
// wireless programming token check - this only works when radio is kept awake to listen for WP tokens
CheckForWirelessHEX(radio, flash, true);
//first send any ACK to request
DEBUG(" [RX_RSSI:");DEBUG(radio.RSSI);DEBUG("]");
if (radio.ACKRequested())
{
radio.sendACK();
DEBUG(" - ACK sent.");
}
DEBUGln();
}
SERIALFLUSH();
flash.sleep();
radio.sleep(); //you can comment out this line if you want this node to listen for wireless programming requests
// LowPower.powerDown(sleepTime, ADC_OFF, BOD_OFF);
DEBUGln("WAKEUP");
}
*/
void readBattery()
{
unsigned int readings=0;
//enable battery monitor on WeatherShield (via mosfet controlled by A3)
pinMode(BATT_MONITOR_EN, OUTPUT);
digitalWrite(BATT_MONITOR_EN, LOW);
for (byte i=0; i<5; i++) //take several samples, and average
readings+=analogRead(BATT_MONITOR);
//disable battery monitor
pinMode(BATT_MONITOR_EN, INPUT); //highZ mode will allow p-mosfet to be pulled high and disconnect the voltage divider on the weather shield
batteryVolts = BATT_FORMULA(readings / 5.0);
dtostrf(batteryVolts,3,2, BATstr); //update the BATStr which gets sent every BATT_CYCLES or along with the MOTION message
if (batteryVolts <= BATT_LOW) BATstr = "LOW";
}
void Blink(byte PIN, byte DELAY_MS)
{
pinMode(PIN, OUTPUT);
digitalWrite(PIN,HIGH);
delay(DELAY_MS/2);
digitalWrite(PIN,LOW);
delay(DELAY_MS/2);
}
Please disregard my previous message.
Here's the correct version of the sketch (WeatherNode) I used:
https://github.com/LowPowerLab/RFM69/blob/master/Examples/WeatherNode/WeatherNode.ino
Some of the compile errors are listed below. I would like to modify the sketch to work with the RF96 transceiver. Any help would be appreciated!
Thank you!
radiohead/RHHardwareSPI.cpp.o: In function `_GLOBAL__sub_I_hardware_spi':
/home/rabin/sketchbook/libraries/radiohead/RHHardwareSPI.cpp:10: multiple definition of `RHHardwareSPI::transfer(unsigned char)'
RadioHead/RHHardwareSPI.cpp.o:/home/rabin/sketchbook/libraries/RadioHead/RHHardwareSPI.cpp:10: first defined here
radiohead/RHHardwareSPI.cpp.o: In function `_GLOBAL__sub_I_hardware_spi':
/home/rabin/sketchbook/libraries/radiohead/RHHardwareSPI.cpp:10: multiple definition of `RHHardwareSPI::attachInterrupt()'
RadioHead/RHHardwareSPI.cpp.o:/home/rabin/sketchbook/libraries/RadioHead/RHHardwareSPI.cpp:10: first defined here
radiohead/RHHardwareSPI.cpp.o: In function `_GLOBAL__sub_I_hardware_spi':