<h3>SparkFun Electronics' preferred foot prints</h3> In this library you'll find all manner of digital ICs- microcontrollers, memory chips, logic chips, FPGAs, etc. We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com. Licensing: Creative Commons ShareAlike 4.0 International - https://creativecommons.org/licenses/by-sa/4.0/ You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. Thin Plasic Quad Flat Package Grid 0.8 mm >NAME >VALUE >NAME >VALUE >NAME >VALUE XTAL + ANT CAPACITOR SMD >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE CTZ3 Series land pattern for variable capacitor - CTZ3E-50C-W1-PF >NAME >VALUE <h3>CAP-PTH-SMALL-KIT</h3> Commonly used for small ceramic capacitors. Like our 0.1uF (http://www.sparkfun.com/products/8375) or 22pF caps (http://www.sparkfun.com/products/8571). Warning: This is the KIT version of this package. This package has a smaller diameter top stop mask, which doesn't cover the diameter of the pad. This means only the bottom side of the pads' copper will be exposed. You'll only be able to solder to the bottom side. >Name >Value >Name >Value >Name >Value >Name >Value >NAME >VALUE >Name >Value RESISTOR SMD >NAME >VALUE >NAME >VALUE >NAME >VALUE RESISTOR chip >NAME >VALUE >NAME >VALUE >Name >Value <h3>AXIAL-0.3-KIT</h3> Commonly used for 1/4W through-hole resistors. 0.3" pitch between holes. Warning: This is the KIT version of the AXIAL-0.3 package. This package has a smaller diameter top stop mask, which doesn't cover the diameter of the pad. This means only the bottom side of the pads' copper will be exposed. You'll only be able to solder to the bottom side. >Name >Value 1/2W Resistor, 0.5" wide Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value 1/4W Resistor, 0.4" wide Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value 1/6W Thru-hole Resistor - *UNPROVEN* >NAME >VALUE 1W Resistor, 0.6" wide Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value 2W Resistor, 0.8" wide Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value >NAME >VALUE RFM69W >NAME >VALUE >NAME >VALUE Capacitor Standard 0603 ceramic capacitor, and 0.1" leaded capacitor. Resistor Basic schematic elements and footprints for 0603, 1206, and PTH resistors. Silicon Labs Si70xx Humidity and Temperature Sensors Version 1.0 (c) 2014 Samuel Lourenço 6-Lead Plastic Dual Flat No Lead Package - 3x3 mm Body [DFN] Source: <a href="http://www.silabs.com/Support%20Documents/TechnicalDocs/Si7006-A10.pdf">http://www.silabs.com/Support%20Documents/TechnicalDocs/Si7006-A10.pdf</a> >NAME >VALUE >NAME >VALUE I2C Humidity and Temperature Sensor Source: <a href="http://www.silabs.com/Support%20Documents/TechnicalDocs/Si7021.pdf">http://www.silabs.com/Support%20Documents/TechnicalDocs/Si7021.pdf</a> Supply Symbols GND, VCC, 0V, +5V, -5V, etc. Please keep in mind, that these devices are necessary for the automatic wiring of the supply signals. The pin name defined in the symbol is identical to the net which is to be wired automatically. In this library the device names are the same as the pin names of the symbols, therefore the correct signal names appear next to the supply symbols in the schematic. <author>Created by librarian@cadsoft.de</author> >VALUE >VALUE SUPPLY SYMBOL SUPPLY SYMBOL >NAME >VALUE + - <h3>SparkFun Electronics' preferred foot prints</h3> In this library you'll find connectors and sockets- basically anything that can be plugged into or onto. We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com. Licensing: Creative Commons ShareAlike 4.0 International - https://creativecommons.org/licenses/by-sa/4.0/ You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE >VALUE >NAME Header 9 Standard 9-pin 0.1" header. Use with straight break away headers (SKU : PRT-00116), right angle break away headers (PRT-00553), swiss pins (PRT-00743), machine pins (PRT-00117), and female headers (PRT-00115).